Siemens C98043-A7002-L4-12 SIMOREG Power Interface Board
Het item werd toegevoegd aan uw offerteaanvraag
Product Information
The Siemens C98043-A7002-L4-12 is a SIMOREG power interface board engineered for variable-speed DC motor drive applications. Designed on a compact 4-layer PCB, this component combines thyristor gate firing pulse generation for six-pulse SCR bridge rectifiers with regulated auxiliary DC power distribution. It delivers linear regulated +24 VDC logic and ±15 VDC analog power rails with low peak-to-peak ripple under 5 mV, maintaining feedback signal integrity for drives handling armature currents up to 2000 A DC. Operating with AC reference input voltages from 380 to 575 V AC, the module maintains tight phase synchronization with a firing angle accuracy of ±0.1° across line frequency variations within ±2 Hz.
In terms of system integration, the C98043-A7002-L4-12 interfaces directly with Siemens SIMOREG DC-MASTER 6RA70 and 6RA24 series DC converters and Central Unit Drive (CUD) control boards. It utilizes pulse transformer galvanic isolation to isolate control logic from high-voltage SCR gate circuits, shielding sensitive processing modules. Commissioning a replacement unit is straightforward because drive configuration and operating parameters are retained in the CUD board's non-volatile memory rather than on the interface board itself. A hardware swap can therefore be carried out directly without necessitating parameter re-entry, with ABC Industrial Parts available to provide pre-tested spare boards to minimize production downtime.
Diagnostic routines for the C98043-A7002-L4-12 are supported via the OP1S operator panel status display and Siemens DriveMonitor commissioning software. When addressing drive faults, initial troubleshooting should include checking the onboard F1 and F2 fuses, measuring internal +24 VDC and ±15 VDC supply rails, and performing oscilloscope checks on the thyristor gate firing trigger pulses. If auxiliary power rails fail or gate pulse outputs deteriorate due to internal board faults, hardware replacement is required. Sourcing a fully tested replacement from ABC Industrial Parts offers a swift resolution to restore full converter functionality in heavy continuous processing lines.
Technical Specifications
| Manufacturer | Siemens |
| Part Number | C98043-A7002-L4-12 |
| Model / Type | Simoreg Power Interface board |
| Product Family | SIMOREG |
| AC Reference Input Voltage | 380-575 V AC |
| Auxiliary Output Logic Voltage | 24 V DC |
| Auxiliary Output Analog Voltage | ±15 V DC |
| Maximum Armature Current Coverage | 2000 A DC |
| Auxiliary Rail Voltage Ripple | <5 mV |
| Firing Angle Accuracy | ±0.1 deg |
| Supply Frequency Tracking Range | ±2 Hz |
| PCB Layer Count | 4-layer |
| Weight | 0.74 kg |
| Operating Ambient Temperature | 0 to 40 °C |
| Storage Temperature | -25 to 70 °C |
| IP Rating | IP00 |
Programming and Configuration
Drive commissioning and diagnostic parameter management for systems using the C98043-A7002-L4-12 are handled through Siemens DriveMonitor commissioning software or the OP1S operator panel. Because the power interface board functions as a physical execution and supply interface, no parameter setup or software flashing is stored on the C98043-A7002-L4-12 PCB itself.
All drive parameters, firing angle computations, and system operating profiles are maintained in the memory of the connected Central Unit Drive (CUD) control board. Replacing a failed C98043-A7002-L4-12 power interface board simply requires establishing physical connections and verifying fuse integrity, allowing immediate operation without loss of custom drive configurations.
Communication and System Integration
The C98043-A7002-L4-12 serves as the primary physical bridge between the CUD control board and the high-power thyristor bridge in SIMOREG 6RA70 and 6RA24 series converters. It processes incoming 380 V AC to 575 V AC reference signals to maintain precise zero-crossing phase tracking and synchronization across a supply frequency tracking range of ±2 Hz.
High-voltage isolation is maintained using integrated pulse transformers, providing galvanic separation between the central drive logic and the thyristor gate-cathode terminals. In addition, the onboard linear regulation delivers isolated +24 VDC logic and ±15 VDC analog supply rails directly to internal measurement circuits, keeping noise levels under 5 mV ripple for accurate current and voltage feedback.
Diagnostics and Status Indication
Monitoring system health on the C98043-A7002-L4-12 is conducted through connected system tools, including the OP1S operator panel and DriveMonitor software diagnostic buffers. System diagnostics detect auxiliary rail undervoltage, phase synchronization loss, or armature current feedback anomalies directly at the CUD level.
Maintenance technicians can perform physical diagnostic verification by measuring the +24 VDC and ±15 VDC voltage levels across the internal supply rails and checking the status of onboard F1 and F2 fuses. Firing trigger pulse integrity to the SCR bridge can be verified using oscilloscope signal inspection at the output terminals.
Replacement and Spare Part Considerations
Replacing the C98043-A7002-L4-12 requires verifying that the replacement board matches the physical specification required for SIMOREG DC-MASTER 6RA70 or 6RA24 converters. The unit features standard board mounting rated at IP00 protection, intended for installation inside the IP-rated drive chassis.
Before restoring power to a newly installed board, technicians should verify incoming AC mains line voltage (380-575 V AC), check gate firing leads for damaged insulation, and ensure that onboard F1 and F2 fuses are intact. Since operating configuration resides on the CUD module, direct replacement restores drive operation without manual parameter restoration.
Error Codes & Fault Codes
The following error codes may be displayed during operation or diagnostics:
| Code | Name | Description | Possible Cause | Recommended Action |
|---|---|---|---|---|
| F001 | Failure of Internal Supply Voltages | Internal auxiliary low-voltage power rail failure or undervoltage detected by CUD | Fault on C98043 power interface board, open F1/F2 fuses, overload on internal 24V or ±15V DC power rails | Check F1/F2 fuses on C98043 board. Measure ±15 VDC and 24 VDC rails. If auxiliary power module is dead or unstable, replace C98043 board. |
| F004 | Phase Angle / Synchronization Fault | Loss of line voltage phase synchronization or zero-crossing reference failure | Failure in zero-crossing detection or PLL tracking circuit on C98043 board, missing main supply line phase | Verify incoming AC mains voltage to drive terminals. If line voltage is present and stable, replace C98043 board. |
| F005 | Armature Current Fault / Firing Synchronization Fault | Armature current feedback anomaly or SCR gate trigger signal loss | Faulty pulse transformer gate drive on C98043 board, damaged gate leads, defective thyristor module | Check gate cabling to thyristors. Oscilloscope check firing pulses from C98043 PCB. Replace C98043 board if gate pulse drive output fails. |
Frequently Asked Questions
Does replacing the C98043-A7002-L4-12 require re-parameterizing the SIMOREG drive?
No. Drive parameters and software settings are stored on the main Central Unit Drive (CUD) memory, allowing a direct hardware swap of the C98043-A7002-L4-12 board without parameter loss.
Which Siemens drive series are compatible with the C98043-A7002-L4-12 board?
The C98043-A7002-L4-12 is compatible with Siemens SIMOREG DC-MASTER 6RA70 series converters and SIMOREG 6RA24 series DC drives.
What diagnostic steps should be taken if fault code F001 appears?
Fault F001 indicates an internal supply voltage failure. Check the onboard F1 and F2 fuses on the C98043-A7002-L4-12 board, measure the 24 VDC and ±15 VDC supply rails, and replace the board if the auxiliary power outputs are missing or unstable.
What causes fault code F004 on a SIMOREG drive with this board?
Fault F004 indicates a phase angle or synchronization failure. First verify that main AC supply line voltage is present at the drive terminals. If line voltage is normal, the zero-crossing detection or phase-locked loop circuit on the C98043-A7002-L4-12 board may be faulty and require board replacement.
How are control logic circuits protected from high voltages on the thyristor gate outputs?
The C98043-A7002-L4-12 uses pulse transformer galvanic isolation to separate low-voltage control circuits from high-voltage SCR gate drive connections.
Take advantage of our exchange formula
A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.
Play it safe with our warranty conditions
Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.
Data backup and recovery
Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.
Specific firmware and hardware versions
If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.
Disclaimer:
We are not an authorised distributor of Siemens.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.