Lenze ESMD752L4TXA smD Frequency Inverter 7.5kW
Het item werd toegevoegd aan uw offerteaanvraag
Product Information
The Lenze ESMD752L4TXA is a 7.5 kW (10 HP) 3-phase AC frequency inverter from the smD series designed for reliable motor speed regulation in industrial control cabinets. Operating across a supply voltage range of 320 to 528 V AC at nominal ratings of 400 V or 480 V AC, this compact IP20-rated unit provides open-loop V/f motor control with configurable linear or quadratic torque curves. The inverter yields continuous output currents of 16.5 A at 400 V AC and 14 A at 480 V AC, with output frequencies spanning from 0 to 240 Hz and a standard switching frequency of 8 kHz. Built for space-saving panel installation, it provides accurate speed control for conveyor systems, process pumps, cooling fans, and general machinery.
Integrating a replacement unit into an existing line centers around Lenze's Electronic Programmable Module (EPM) architecture. The drive features a pluggable EPM memory chip on its front panel, which stores all user parameter settings, motor profiles, and operating limits. When swapping a failed unit, maintenance personnel can transfer the existing EPM memory chip directly into the replacement ESMD752L4TXA without connecting communication cables or executing software programming routines. Control signal interfaces include four freely programmable digital inputs, one flexible analog input supporting 0-10 V, 0-20 mA, or 4-20 mA setpoint signals, and one status relay output. Optional fieldbus modules can also be installed to integrate the drive into Modbus RTU or CANopen networks. If parameter extraction from a faulty donor unit is required prior to replacement, ABC Industrial Parts offers technical assistance to ensure smooth commissioning.
Diagnostic monitoring is handled through an integrated 3-digit LED keypad display on the front face of the inverter. During normal operation, the display presents runtime parameters such as output frequency or motor load, while active fault conditions trigger specific code indications ranging from F0 through F9. Initial troubleshooting should involve verifying line supply voltage, checking motor and output cable wiring for ground faults or short circuits, inspecting cooling fins and fan operation for overheating, and verifying fieldbus connections. While environmental, supply, or wiring issues can be resolved at the cabinet level, internal power or control board component failures trigger an F0 code, indicating a hardware fault that is not field-serviceable. In these instances, sourcing a fully tested exchange drive or replacement unit from ABC Industrial Parts provides a rapid path back to full operational status.
Technical Specifications
| Manufacturer | Lenze |
| Part Number | ESMD752L4TXA |
| Product Family | smD |
| Component Type | Frequency Inverter |
| Rated Power (kW) | 7.5 kW |
| Rated Power (HP) | 10 hp |
| Nominal Supply Voltage | 400/480 V AC |
| Supply Voltage Range | 320 - 528 V AC |
| Output Current@ 400V | 16.5 A |
| Output Current @ 480V | 14 A |
| Output Frequency | 0 - 240 Hz |
| Switching Frequency | 8 kHz |
| Control Method | V/f Control |
| Digital Inputs | 4 |
| Analog Inputs | 1 (0-10V, 0-20mA, 4-20mA) |
| Relay Outputs | 1 |
| IP Rating | IP20 |
Programming and Configuration
Configuration of the Lenze ESMD752L4TXA frequency inverter revolves around the pluggable Electronic Programmable Module (EPM). All drive parameters, including acceleration/deceleration ramps, setpoint scaling, and thermal overload thresholds, are stored directly on this small memory chip located on the drive's front panel. Drive setups can be created locally using the built-in 3-digit LED keypad or cloned offline using an optional EEPM1RA EPM Programmer.
The inverter supports open-loop V/f control, allowing users to configure linear or quadratic characteristic curves based on application demands. Setpoints can be commanded via the flexible analog input terminal, which accepts 0-10 V DC, 0-20 mA, or 4-20 mA standard industrial signals. Transferring parameters between drives requires no active power supply on the target drive when using external programmer tools, ensuring rapid deployment across multiple machines.
Communication and System Integration
The ESMD752L4TXA is equipped with standardized control terminals for straightforward integration into automated systems. The terminal strip includes four programmable digital inputs for start/stop, direction, preset speeds, or external fault trips, along with one configurable analog input and one status relay contact for fault signaling or operational status feedback.
For centralized automation networks, the smD inverter platform supports fieldbus integration via add-on communication modules. Optional interface modules enable direct connection to Modbus RTU or CANopen networks, allowing main controllers to transmit speed setpoints, monitor operating status, and capture diagnostic flags remotely.
Diagnostics and Status Indication
Real-time diagnostic feedback is provided by the integrated 3-digit LED display located on the front face of the drive. The display indicates active operational parameters during normal running conditions and displays dedicated fault codes (F0 through F9) when abnormal conditions occur. Operators can navigate through the keypad menu to inspect active alarms and review stored fault history parameters for fast root-cause evaluation.
Status LED Indicators
| LED | Color/Status | Meaning |
|---|---|---|
| 3-Digit LED Display | Red/Green - Numeric display | Displays operational status (e.g., output frequency, load) or active fault codes (F0-F9) |
Replacement and Spare Part Considerations
When replacing an ESMD752L4TXA frequency inverter, verify that the prospective unit matches the 7.5 kW (10 HP) rating and supply voltage specifications (320-528 V AC, 3-phase). Because parameter data resides on the removable EPM chip, swapping the chip from the original drive into the replacement unit transfers all operating parameters immediately, eliminating the need to connect programming tools.
Ensure power is fully disconnected before removing or inserting the EPM module to prevent parameter corruption or triggering fault code F1. If migrating to a modern product line during a system retrofit, Lenze recommends the i510 or i550 cabinet inverter series as the standard upgrade pathway.
Error Codes & Fault Codes
The following error codes may be displayed during operation or diagnostics:
| Code | Name | Description | Possible Cause | Recommended Action |
|---|---|---|---|---|
| F1 | EPM Fault / Control Fault | Electronic Programmable Module missing, corrupted, or improperly seated. | EPM chip missing, damaged, unformatted, or inserted while drive was powered. | Power off drive, properly seat a valid EPM module into front socket, and re-power unit. If problem persists, re-program EPM or replace EPM module. |
| F2 | Overcurrent | Drive peak output current limit exceeded. | Short circuit or ground fault at motor/output cable, acceleration time too fast, motor overload, or heavy transient mechanical load. | Check motor and output wiring for short circuits and ground faults. Increase acceleration ramp time. Check motor sizing. |
| F3 | Overvoltage | DC bus voltage exceeded safe operating upper limit. | Deceleration ramp time too short causing regenerative energy back-feed, high AC mains input voltage, or dynamic braking resistor failure/missing. | Extend deceleration time, verify AC line input voltage, or install/check dynamic braking unit/resistor. |
| F4 | Undervoltage | DC bus voltage dropped below minimum operating threshold. | AC mains supply voltage dropped below minimum, supply phase loss, incoming line fuse blown, or transient power dip. | Check input supply voltage, check supply line fuses and connections. |
| F5 | Heatsink Overtemperature | Heatsink temperature exceeded internal trip limit. | Inadequate ventilation, clogged cooling fins, cooling fan failure, ambient temperature too high, or excessive continuous drive load. | Clean heatsink cooling fins, check cooling fan operation, ensure adequate cabinet ventilation and clearance around unit. |
| F6 | Motor Overload (I2t) | Motor thermal overload trip calculated by internal I2t algorithm. | Motor operated at high load at low speed for prolonged period, improper motor thermal current parameter setting, or mechanical overload. | Check motor current setting, verify motor mechanical loading and cooling, allow motor to cool before resetting. |
| F7 | Drive Overload | Continuous overload threshold of the drive inverter exceeded. | Drive undersized for load requirement or excessive duty cycle overload. | Reduce drive load or upgrade to a larger capacity frequency drive. |
| F8 | External Fault | External fault trip triggered via digital input. | Digital input programmed for external fault trip was activated/opened. | Inspect external interlock device or sensor connected to the designated digital input terminal. |
| F9 | Communication Fault | Loss of communication connection on optional fieldbus interface. | Disconnected fieldbus cabling, master offline, noise interference, or incorrect baud rate / address. | Check bus cable connection, master controller state, and network termination. |
| F0 | Internal Hardware Fault | Internal control board or power section failure detected. | Internal component failure on control or power board. | Internal hardware fault — non-field-serviceable. Return drive for service or replace unit. |
Frequently Asked Questions
How do I transfer parameters to a replacement Lenze ESMD752L4TXA inverter?
Parameters are stored on the pluggable Electronic Programmable Module (EPM) located on the front panel. With power completely disconnected, remove the EPM chip from the original drive and insert it into the front socket of the replacement unit.
What does fault code F1 mean on the ESMD752L4TXA drive?
Fault code F1 indicates an EPM or control fault. This occurs if the EPM memory module is missing, corrupted, unformatted, improperly seated, or inserted while the drive is powered. Turn off power, firmly seat a valid EPM chip, and re-apply power.
What does fault code F0 signify?
Fault code F0 indicates an internal hardware failure on either the power section or control board. This fault cannot be serviced in the field; the drive must be returned for repair or replaced.
What fieldbus communication options are supported by the smD series?
The drive supports fieldbus communication via optional add-on modules, including Modbus RTU and CANopen interface options.
What is the recommended modern replacement for the Lenze smD series?
For modern system upgrades or new cabinet installations, Lenze recommends migrating to the i510 or i550 series cabinet frequency inverters.
Take advantage of our exchange formula
A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.
Play it safe with our warranty conditions
Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.
Data backup and recovery
Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.
Specific firmware and hardware versions
If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.
Disclaimer:
We are not an authorised distributor of Lenze.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.